Fujitsu SPARC T5440 Manual do Utilizador Página 150
- Página / 214
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
124 SPARC Enterprise T5440 Server Service Manual • July 2009
FIGURE: Removing the IDPROM
2. Place the IDPROM on an antistatic mat.
▼ Install the IDPROM
Before you begin, complete these tasks:
■ Read the section, “Safety Information” on page 59.
■ Power off the server, using one of the methods described in the section, “Powering
Off the System” on page 63.
■ “Extend the Server to the Maintenance Position” on page 66
■ “Disconnect Power Cords From the Server” on page 65
■ “Perform Electrostatic Discharge – Antistatic Prevention Measures” on page 69
■ “Remove the Top Cover” on page 69
■ “Remove the Service Processor” on page 120
- SPARC Enterprise 3
- T5440 Server 3
- Service Manual 3
- Contents 7
- Field-Replaceable Units 176 14
- Index 179 14
- For Safe Operation 15
- Before You Read This Document 15
- Related Documentation 17
- Title Description Manual Code 18
- UNIX Commands 19
- Text Conventions 19
- Prompt Notations 20
- Notes on Safety 21
- Task Warning 22
- Product Handling 23
- Alert Label 24
- Preface xxiii 25
- Identifying Server Components 27
- Front Panel Diagram 29
- Front Panel LEDs 30
- Rear Panel Diagram 31
- Rear Panel LEDs 33
- Ethernet Port LEDs 34
- Managing Faults 35
- Diagnostic Flowchart 37
- Diagnostic Flowchart Actions 38
- Managing Faults 13 39
- ILOM Overview 41
- ILOM Fault Management 42
- SunVTS Overview 44
- Managing Faults 19 45
- Managing Faults 21 47
- Managing Faults 23 49
- Managing Faults 25 51
- Controlling How POST Runs 52
- ▼ Change POST Parameters 53
- ▼ Run POST in Maximum Mode 54
- Managing Faults 29 55
- Detecting Faults 56
- Command” on page 33 57
- Commands 61
- ▼ Check the Message Buffer 62
- ▼ View ILOM Event Log 63
- Managing Faults 39 65
- SunVTS Software Packages 67
- Detecting Faults Using POST 68
- Clearing Faults 73
- Managing Faults 49 75
- Disabling Faulty Components 76
- ▼ Disable System Components 78
- ▼ Re-Enable System Components 78
- ILOM-to-ALOM CMT Command 79
- Reference 79
- Managing Faults 55 81
- Safety Information 85
- Safety Symbols 86
- Antistatic Wrist Strap 87
- Antistatic Mat 87
- Required Tools 88
- Remotely 88
- Powering Off the System 89
- Position 91
- 1 Slide Rail Lock 92
- 2 Inner Rail Release Button 92
- Figure Legend 94
- Removing the Top Cover 95
- Servicing Hard Drives 98
- Removing a Hard Drive 100
- # cfgadm -al 100
- Installing a Hard Drive 102
- # cfgadm -c configure c0::sd1 102
- ▼ Remove a Hard Drive 103
- ▼ Install a Hard Drive 104
- Hard Drive Device Identifiers 105
- Hard Drive LEDs 106
- Servicing Fan Trays 107
- Next Steps 108
- ▼ Remove a Fan Tray 109
- ▼ Install a Fan Tray 110
- Fan Tray Device Identifiers 110
- Fan Tray Fault LED 110
- Servicing Power Supplies 111
- Removing a Power Supply 113
- Installing a Power Supply 114
- ▼ Remove a Power Supply 115
- ▼ Install a Power Supply 116
- Power Supply LED 117
- Servicing PCIe Cards 118
- ▼ Remove a PCIe Card 119
- ▼ Install a PCIe Card 120
- ▼ Add a PCIe Card 120
- PCIe Device Identifiers 122
- Related Information 123
- Servicing CMP/Memory Modules 124
- ▼ Remove a CMP/Memory Module 125
- ▼ Install a CMP/Memory Module 126
- ▼ Add a CMP/Memory Module 127
- Servicing FB-DIMMs 130
- ▼ Remove FB-DIMMs 131
- ▼ Install FB-DIMMs 131
- ▼ Verify FB-DIMM Replacement 132
- ▼ Add FB-DIMMs 135
- FB-DIMM Device Identifiers 138
- Servicing the Front Bezel 141
- ▼ Remove the Front Bezel 142
- ▼ Install the Front Bezel 143
- Servicing the DVD-ROM Drive 144
- ▼ Install the DVD-ROM Drive 145
- Servicing the IDPROM 149
- ▼ Install the IDPROM 150
- Servicing the Battery 151
- Servicing the Motherboard 161
- ▼ Install the Motherboard 163
- Installing the Motherboard 164
- Servicing the Front I/O Board 172
- ▼ Remove the Front I/O Board 173
- ▼ Install the Front I/O Board 174
- ▼ Install the Top Cover 176
- 1 Inner rail release button 178
- 2 Slide rail lock 178
- ▼ Power On the Server 179
- I/O Connections to CMP/Memory 182
- ● Do one of the following: 187
- System Bus Topology 188
- Connector Pinouts 193
- 1 Request to Send 5 Ground 194
- 4 Ground 8 Clear to Send 194
- Serial Port Connector Pinouts 195
- USB Connector Pinouts 196
- Connector Pinouts 171 197
- Server Components 199
- Customer-Replaceable Units 200
- Field-Replaceable Units 202
- Numerics 205
- Index 181 207
- Index 183 209
- Index 185 211
Manuais e produtos relacionados com Computadores Fujitsu SPARC T5440
Computadores Fujitsu Service View Resource Orchestrator Cloud Edition V Manual do Utilizador
(102 páginas)
(102 páginas)
Computadores Fujitsu 2000 Manual do Utilizador
(66 páginas)
(66 páginas)
Computadores Fujitsu M3000 Manual do Utilizador
(76 páginas)
(76 páginas)
Computadores Fujitsu ServerView Respurce Orchestrator Virtual Edition V Manual do Utilizador
(247 páginas)
(247 páginas)
Computadores Fujitsu BX900 S1 Manual do Utilizador
(142 páginas)
(142 páginas)
Computadores Fujitsu M5000 Manual do Utilizador
(310 páginas)
(310 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais