Fujitsu SPARC ENTERPRISE M3000 Manual do Utilizador descarregar pdf (Página 54)

3-2 SPARC Enterprise M3000 Server Service Manual • November 2009

2. Remove the power cord clamp and disconnect the cable.

FIGURE 3-1 Power-off Method

3.2 Failure Diagnostic Method

When an error occurs, a message is displayed on the maintenance monitor in many

cases. Use the flowchart in

FIGURE 3-2 to find the correct methods for diagnosing

failures.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 211 212

SPARC Enterprise 3
M3000 Server 3
Service Manual 3
Contents 7
Contents vii 9
Contents ix 11
Contents xi 13
Abbreviations Abbreviations–1 14
Index Index–1 14
Glossary 15
M3000 Server Documentation 17
Book titles Manual codes 18
Preface xvii 19
Text Conventions 20
Prompt Notations 20
This Product 21
Alert messages in the text 22
Notes on Safety 23
Ω. The grounding 24
Preface xxiii 25
Alert Labels 26
Product Handling 27
Limitations and Cautions 28
Preface xxvii 29
1.1 ESD Precautions 31
1.2 Server Precautions 33
Hardware Overview 35
Server (Front View) 37
123456 7 38
2.2 Operator Panel 39
2.2.1 Operator Panel Overview 40
Switches (Operator Panel) 41
Mode Switch Function 42
LEDs on the Operator Panel 43
TABLE 3-1 45
789101112 48
2.5 Labels 51
Label Locations 52
Outside: Standards label 52
Troubleshooting 53
3.2 Failure Diagnostic Method 54
Diagnostic Method Flowchart 55
Configuration 56
XSCF> showhardconf 57
Configurations 58
# showrev 59
XSCF> version 59
3.4 Error Conditions 60
Chapter 3 Troubleshooting 3-9 61
3.4.2 Monitoring Output 62
3.4.3 Messaging Output 62
XSCF> showstatus 67
FANBP_B Status:Normal; 67
XSCF> 67
3.5.4.1 fmdump -V Command 68
3.5.5 Using the fmadm Command 69
3.5.5.2 fmadm repair Command 70
3.5.5.3 fmadm config Command 70
Commands 71
3.6.1.1 Options 72
3.6.2.1 Options 73
3.6.3.1 Options 76
The prtconf output continued: 77
3.6.4.1 Options 78
3.6.5 Using the ping Command 79
3.6.6 Using the ps Command 80
3.6.6.1 Options 81
3.6.7.1 Options 82
FRU Replacement Preparation 83
4.2.1 FRU Replacement 84
4.2.2 FRU Installation 85
# cfgadm -a 87
# cfgadm -c unconfigure Ap_Id 87
# cfgadm -c configure Ap_Id 88
TABLE 2-3 and TABLE 2-5 93
4.5.1 Powering off the Server 94
4.5.3 Powering on the Server 95
XSCF> poweron -a 96
Internal Components Access 101
FIGURE 5-1) 102
5.2.1 Removing the Top Cover 103
5.2.2 Attaching the Top Cover 104
5.3.1 Accessing the Air Duct 105
5.3.2 Removing the Air Duct 105
5.3.3 Attaching the Air Duct 106
5.4.1 Removing the Fan Cover 107
5.4.2 Attaching the Fan Cover 108
Motherboard Unit Replacement 109
Motherboard Unit Location 111
1 Memory (DIMM) 112
2 PCIe card 112
3 Shutter unit 112
12. Remove the shutter unit 114
Removing the Motherboard Unit 116
6.4 Reassembling the Server 117
10. Check the hardware 118
Location number Component 120
7.1 Memory Mounting Rules 121
2. Mount DIMMs in group B 124
7.2 Accessing the DIMMs 125
7.3 Removing the DIMMs 126
7.4 Installing the DIMMs 127
7.5 Reassembling the Server 127
PCIe Cards 129
PCIe Slot Locations 130
8.1 Accessing a PCIe Card 131
8.2 Removing a PCIe Card 132
8.3 Mounting a PCIe Card 132
8.4 Reassembling the Server 133
Hard Disk Drive (HDD) 135
Hard Disk Drive Location 136
FIGURE 9-2)to 137
FIGURE 9-2) 137
Removing a Hard Disk Drive 138
9.4 Reassembling the Server 139
Replacing the Hard Disk Drive 141
Backplane 141
FIGURE 10-2) 144
10.4 Reassembling the Server 146
CD-RW/DVD-RW Drive Unit 147
(DVDU) Replacement 147
FIGURE 11-2) 149
FIGURE 11-2), push the CD 150
11.4 Reassembling the Server 151
Power Supply Unit Replacement 153
1 Power supply unit (PSU#0) 154
2 Power supply unit (PSU#1) 154
XSCF> replacefru 155
FIGURE 12-2) 156
12.4 Reassembling the Server 157
Fan Unit Replacement 159
Fan Unit Locations 160
13.1 Accessing a Fan Unit 161
13.2 Removing a Fan Unit 161
Removing a Fan Unit 162
13.3 Mounting a Fan Unit 163
13.4 Reassembling the Server 163
Fan Backplane Replacement 165
Fan Backplane Location 166
FIGURE 14-2), and incline 167
FIGURE 14-2) 167
Removing the Fan Cage 168
FIGURE 14-3) 169
14.4 Reassembling the Server 170
Operator Panel Replacement 173
Operator Panel Location 174
2. Loosen the one thumbscrew 176
15.4 Reassembling the Server 177
Components List 179
FRU List 183
B.2 Motherboard Unit 184
B.2.1 Memory (DIMM) 185
B.2.2 PCIe Slot 185
B.2.3 CPU 186
B.2.4 XSCF Unit 186
B.3 Drive 187
B.4 Power Supply Unit 188
B.5 Fan Unit 189
APPENDIX 191
C.1 Serial Port 192
C.2 UPC Port 192
C.3 USB Port 193
C.4 SAS Port 193
D-sub 9pin 194
UPS Controller 195
D.2 Signal Cable 196
Appendix D UPS Controller D-3 197
D.4 Power Supply Conditions 198
D.5 UPS Cable 199
D.6 Connections 200
DC Power Supply Model 201
E.1 The Server Views 202
Electrical Specifications 205
Abbreviations 207

Comentários a estes Manuais

Sem comentários

Fujitsu SPARC ENTERPRISE M3000 Manual do Utilizador Página 54

Comentários a estes Manuais

Manuais e produtos relacionados com Computadores Fujitsu SPARC ENTERPRISE M3000