Fujitsu fi-4750C Manual do Utilizador

Operator's Guidefi-4750C Image ScannerC150-E182-01EN

viii

ixCOMPONENTSINSTALLATION AND CONNECTIONSOPERATING INSTRUCTIONDOCUMENT SPECIFICATIONSCANNER SPECIFICATIONSCONSUMABLES AND OPTIONSSETUP MODEGLOSSARY OF

1CHAPTERCOMPONENTSThis chapter describes the components of the scanner, part names, operatorpanel arrangement, and the function of parts and LED indic

1-11Checking the ComponentsThese high precision components must be handled carefully.Confirm that all the components shown in the following figure ha

1-2Units and AssembliesThis section shows the exterior view and assemblies of the scanner. This section also provides the nameof each part and descr

1-3No.Part Function1 Document coverCloses over and keeps in place the document to beread.2 Document bed Holds document to be read. Also called Flatbe

1-4StackerThumb screwGuide A ASYPick roller 2Pick roller 1Pad ASYAssemblies

1-5Operator panelExitEnterStopPreviousNextSend To/StartReadCheckOperator PanelThe operator panel is located on the upper right hand side of the scann

1-6Name of the button andLEDFunctionButton NextDisplays the next LCD screen.PreviousDisplays the previous LCD screen.Moves the cursor to the left.Mov

1-7Counter DisplayThe scanner is provided with a counter display. NOTICEWhen the counter value is 0, no number is displayed.Paper counterAbrasion cou

fi-4750CImage ScannerOperator's Guide

1-8Operation statusThe operation status is indicated by the following messages:<Power-on><Reading><Waiting for Start> The scanner d

1-9Temporary error<Hopper empty>This message is displayed if there is no more paper on the ADF paperchute during a read operation in ADF mode.

1-10AlarmOne of the following messages is displayed if an error occurs in the scanner. If one of the following errormessages is displayed, turn the p

1-11<Image transfer alarm><Memory alarm><EEPROM alarm><FAN alarm><IPC Board alarm>

1-12

2CHAPTERINSTALLATION AND CONNECTIONSThe chapter describes how to install and connect the scanner.PrecautionsInspectionRepositioning the Shipping LockC

2-1PrecautionsThis section describes precautions to follow when installing the scanner.To ensure the longevity and proper functioning of your scanner

2-2InspectionThis section describes how to check the labels.Position of two labelsLabel A (Example; your actual label may differ)Indicates regulation

2-3Repositioning the Shipping LockTo keep the scanner from being damaged during shipping, the carrier unit is fixed with a Shipping Lock.After placin

2-4Cable ConnectionsThis section describes how to connect the cables.Connect the cables as follows: Turning the power switch OffPress the “O” side of

iRevisions, DisclaimersFCC declaration: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Pa

2-5 Connecting the interface cablesConnect the SCSI interface cables and secure them. NOTICES1. Factory default for the SCSI terminator is On. If the

2-6Mounting the StackerMount the stacker using the following procedure.1Mount the stacker.Hook the pins on the stacker to the claws on the image scan

2-7Setting the SCSI ID and the SCSI TerminatorThe default of the SCSI ID is 5. The SCSI ID is set by using the Setup mode of the operator panel. Thep

2-8

3CHAPTEROPERATING INSTRUCTIONThis chapter describes how to turn the power on, and gives button specifica-tions and reading mode settings for both ADF

3-1Turning the Power OnThis section describes how to turn the power On.Press the “I” side of the power switch. The power turns On and the green Powe

3-2Waking up the Scanner from the Low Power ModeThis section describes how to wake up thescanner from the Low Power Mode.To wake up the Scanner, simp

3-3Manual Feed Mode SettingIn this mode, the scanner waits for some predetermined time before issuing a “Paper Empty” messageafter all documents are

3-4Loading Documents on the ADF NOTICEBe sure to change the position of the shipping lock according to the “Installation and Connection”procedure bef

3-52Fan the sheets before setting a stack ofdocuments on the ADF paper chute. Fordetails see the next page.• Place the documents face down, with the

iiThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conformme à la norme NMB-003 duCanada.As an

3-6 NOTICESNote the following when preparing the paper.• Remove paper clips and staples. Flatten the staple holes.• Read the following documents usin

3-7Guide lever(Both sides)DocumentsGuidemax. 8 mm(0.32")4Set the guides so that there is a smallclearance between the document edgesand the guid

3-8Loading Documents on the Flatbed CAUTIONDo not look directly at the light source during the read operation.Scanner parts involved when loading doc

3-9Loading Documents Larger than the Document Bed CAUTIONDo not look directly at the light source during read operation.1Open the Document cover to a

3-10Reading a Page from a Thick Book CAUTIONDo not look directly at the light source during the read operation.1Open the Document cover.2Place the bo

3-12

4CHAPTERADF DOCUMENT SPECIFICATIONThis chapter describes the document size and document guality required touse the ADF successfully.Document SizeDocu

4-1Document SizeThe following figure shows document sizes that the scanner can read using the ADF.(Unit : mm)ScannerMaximumMinimumAB A Bfi-4750C297 (

4-2Document QualityThis section describes the types and weights of paper that the scanner can read and precautions inpreparing documents to ensure ma

4-3Less than3 mmFeed directionTop of the paperRead surfaceMore than30 mmFeed directionLess than5 mmMore than30 mmRead surfaceTop of the paper CAUTION

iiiFujitsu OfficesPlease send your comments on this manual or on Fujitsu products to the followingaddresses:FUJITSU COMPUTER PRODUCTS OFAMERICA,INC.29

4-4B4677952396141503325315010010080604020052 64 81 104 127A3ADF chuteloading(number ofpages)A4/Letter or smalleror Double LetterADF Capacity g/m2ADF

4-5Areas not to be PerforatedWith the ADF, perforations in the shaded areas may cause errors. If you must read data from such apaper, use the flatbed

4-6Grounding Color AreasThe shaded area in the Figure below should have paper grounding color (white) or drop-out color. If not,turn the white level

4-7Double Feed Detection ConditionWhen the double-feed sensor is used, the thickness or the combination of the thickness and the length ofthe documen

4-8Job Separation Sheet1 ShapeThe following shows the typical format of the job separation sheet.2 Paper conditionsThe paper conditions are the same

5CHAPTERSCANNER SPECIFICATIONSThis chapter describes the basic product specifications, installation specifica-tions, and dimensions.Basic Product Spec

5-1Basic Product SpecificationNotes *1: The details are described in chapter 4.*2: The actual scanning speed might differ due to host computers’ envi

5-2Installation SpecificationThe following table lists the installation specifications of the scanner.Item SpecificationDimensions (mm)(Without Hoppe

5-3(unit: mm)521234335445 696(17.5") (27.4")(13.2")(9.2")(20.5")Dimensions

5-4

ivNote, LiabilityREAD ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IFNOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERSOR BYSTAND

6CHAPTERCONSUMABLES AND OPTIONSThis chapter describes the consumables and options.ConsumablesOptionsVideo Interface OptionIPC-4D Option

6-1ConsumablesThe following table lists consumables used for the scanner. Be sure to keep some consumables in stock.The customer is responsible for

6-2OptionsThe following table lists options available for the scanner.Contact your Fujitsu sales agent for more information.Name P/N RemarksVideo Int

6-3Video Interface Option How to Install the Video Interface Option Board1Loosen the two screws to remove theplate. CAUTIONTurn Off the power before

6-4 Reading Mode Setting When the Video Interface Option is InstalledThis section describes the button specifications and setup details for reading m

6-5<Screen 6>9 Select Front Density by pressing or. As the cursor moves to the right, / may appear. Then press. The scanner displays

6-6<Screen 9>12 Select Back Halftone (when “Duplex” wasspecified) by pressing or . Theparameters are the same as in step 11.Press to conf

6-7IPC-4D OptionThe IPC-4D option performs the image processing.IPC-4D supports the following image processing. Item Description Pre-Filter Ball-Po

6-8

7CHAPTERSETUP MODEThis chapter describes the setup mode of the scanner.Activating the Setup ModeContents of the Setup Mode

vPrefaceThis manual explains how to use the fi-4750C image scanner.This manual contains chapters on the following topics:COMPONENTSINSTALLATION AND CO

7-1Activating the Setup ModeThis section describes how to activate the setup mode.<Screen M1>1 Turn the power On. Then the scannerdisplays “Sca

7-2Contents of the Setup ModeThis section describes the contents of the setup mode.NoItem DescriptionSelectableparametersDefault1 Double feed checkSp

7-3(Continued)* This offset refers to the difference from the value adjusted by automatic offset adjustment.** Some restrictions apply to the detecti

7-41. Setting double feed detection (Paper Thickness)When you set the use of double feed detection, you must set it as follows:<Screen 41>1 Pr

7-52. Setting double feed detection (Paper Length)<Screen 42>1 Press or and let the scannerdisplay Screen 42.2 Press either the or but

7-63. Setting IPC pre-set modeWhen you set the use of the IPC pre-set mode, you must set it as follows:1 Press “Next” or “Previous” and let thes

7-74. Reset of the abrasion counterWhen you reset the abrasion counter, you must set it as follows:1 Press “Next” or “Previous” and let thescan

7-86. Setting the time-out limit1 Press “Next” or “Previous” and let thescanner display Screen 46.<Screen 46>2 At Screen 46, press to i

7-9<Screen B (Example of ADF Front Offset)>4 At Screen B, press to increase the offsetor press to decrease offset.The increment or decremen

7-1010. IPC Status Display<Screen 50> (An example)1 Press “Next” or “Previous” and let thescanner display Screen 50.<Screen 50-1>2

viConventionsImportant information that requires special attention is indicated as follows: WARNINGWARNING indicates that serious personal injury may

7-1113. Low Power Mode Setting<Screen 53>1 Press “Next” or “Previous” and let thescanner display Screen 53.2 At Screen 53, press or

7-1215. Display the TPS Board ID Number<Screen 55> (An Example)1 Press “Next” or “Previous” and let thescanner display Screen 55.The scan

7-1317. Adjust ADF Erasing Edges<Screen 57>1 Press “Next” or “Previous” and let thescanner display Screen 57.2 At Screen 57, press or

7-1418. Adjust FB Erasing Edges<Screen 58>1 Press “Next” or “Previous” and let thescanner display Screen 58.2 At Screen 58, press or

7-1519. Select Light Source in Unicolor Reading<Screen 59>1 Press “Next” or “Previous” and let thescanner display Screen 59.2 At Screen 5

7-16

GL-1GLOSSARY OF TERMSA4 sizeA standard paper size. Paper size is 210 x 297 mm.A5 sizeA standard paper size. Paper size is 148 x 210 mm.A6 sizeA sta

GL-2Double feed detectionA scanner function which detects the accidental feeding of multiple sheets by the ADF unit. Can be turnedon or off by the op

GL-3HexadecimalA base-16 numbering system (also commonly referred to as hex numbers). Since a base-16 systemrequires 16 digits, numbers 0 through 9

GL-4Mirror imageThe read image is symmetrically flipped to produce a mirror image of the original detected in the mainscanning direction.Noise remova

viiviiCONTENTS❑❑❑❑❑CHAPTER 1 COMPONENTSChecking the Components...1-1U

GL-5Serial interfaceA standard computer interface. Information is transferred between devices over a single wire (althoughother wires are used for c

GL-6

IN-1INDEXAbrasion counter 1-7Activating the Setup mode 7-1ADF 1-2, 1-3ADFerasing edges 7-13lever 1-2, 1-3mode 1-9paper chute 1-2

IN-2Precautions 2-1, 4-2Preface vPrevious button 1-6Readingmode 6-4face 6-4Resetting abrasion counter 7-2, 7-7Resolution 6-4Scan